Thumb Tabs for Leatherman Surge 3d printed
Thumb Tabs for Leatherman Multitools
Tritium Thumb-Tabs for the Leatherman FREE P4 & P2 3d printed
Thumb Tabs for Leatherman Wave or Charge 3d printed Fits either Wave or Charge
Thumb Tab for the FREE T2 or T4 3d printed
Thumb Tabs for Leatherman Surge 3d printed
Thumb Tabs for Leatherman Multitools

Thumb Tabs for Leatherman Multitools

Regular price $16.00
/
Shipping calculated at checkout. This item typically ships in 1-2 Weeks

Tool
Type

New Lower Price (Grey only)

Design:

The blades on Mulitools are sometimes difficult to grip, or even impossible to deploy if your wearing gloves. These sturdy nylon thumb tabs are designed to solve the problem.

The tabs have a lightly textured surface, and provide a good grip. 


#Regular-FREEP4orP2orARC

Three tabs, connected on a sprue. See separating tabs below.

Each tab is unique: A symbol is etched on the back of the two smaller tabs to help you determine which one to place on the saw, and which to place on the serrated blade.

The FREE series tabs will also fit the Mr. Crunch Leatherman Garage tool, Garage #005, and the Leatherman ARC

Tritium Vial Design
#TritiumCompatible

Three tabs, connected on a sprue. See separating tabs below.

Another customer requested product. Tritium vials are a great way to add color, and nighttime visibility to your multitool. These thumb-tabs are designed to hold 2x12mm tritium vials. Note the vials are not included. The tabs can also be filled with glow-in-the-dark resin for a similar look.

Tritium Vials
#TritiumCompatible

Designed to fit 2x12mm vials. (Not included) Any crystal clear UV adhesive should work. NOA68 is the best adhesive to use as it is designed to bond glass to plastics.

Don't separate the tabs for easier handling. Place a tritium vial into the recess in each tab, it should be a snug fit, but don't ever force the vials into place as they are made from glass.

Flip the assembly over, and apply a small amount of UV adhesive into the opening on the backside of the tab.  Just enough to hold the vial in place. Before curing you can check the assembly and clean up any excess adhesive.

Place the assembly under a UV curing lamp with a wavelength appropriate to the UV resin you use. First with the tritium vials facing upwards, then flip it over and finish curing the backside.

Double check that the adhesive is cured by touching the backside with a needle.

Attaching the tabs to the tool:
#TritiumCompatible

The tabs may be held to the tool  the same UV curing glue as the tritium vials, or you may use super glue.

To install: Insert the tabs into the blade, ensuring they sit flush with surface of the blade. And that the knurled side faced towards the inside of the tool.

Flip the blade over and apply a drop of glue to the edge between the blade and the tab. The glue will absorb into the plastic, and also into the seam. If any super glue gets onto the blade, wait about twenty seconds, and gently clean using a lint-free cloth with a small mount of Acetone applied to it.
If you used UV glue, place the whole blade under a UV curing lamp as you did with the vials.

Removing glued thumb tabs:
#TritiumCompatible

Click here to watch the video showing how to remove the thumb-tabs.

Acetone can be applied to the back of the tab using a cotton swab soaked in acetone.  Allow the acetone to absorb into the nylon, then wait about thirty seconds before pushing the tab out from the back side. Clean up any glue residue using more acetone.

You can also soften the glue by gently heating up the blade to above 120°C. The nylon does not melt until over 200°C. (Do not apply heat directly to the plastic).


Attaching the tabs:
#Regular

Super glue method:

Use super-glue (cyanoacrylate). You will also need Acetone to clean up any overflow of glue. To install: Insert the tabs into the blade, ensuring they sit flush with surface of the blade. Flip the blade over and apply a drop of super glue to the seam between the blade and the tab. The glue will absorb into the plastic, and also into the seam. If any glue gets onto the blade, wait about twenty seconds, and gently clean using a lint-free cloth with a small mount of Acetone applied to it.

Removing super glued thumb tabs: Click here to watch the video showing how to remove the thumb-tabs. Acetone can be applied to the back of the tab using a cotton swab soaked in acetone.  Allow the acetone to absorb into the nylon, then wait about thirty seconds before pushing the tab out from the back side. Clean up any glue residue using more acetone.  You can also soften the glue by  gently heating up the blade to above 120°C. The nylon does not melt until over 200°C. (Do not apply heat directly to the plastic).

#Regular-FREEP4orP2orARC #Regular-FREET2ORT4

Screw method (FREE Series only):

Screws not included

The specs on the six set screws are M2x4mm set screws  or #1-72 thread, 5/32" long
These can be found at a good hardware shop that carries small screws, as well as eBay and Amazon.com

A 0.035" size hex driver is needed for the above #1-72 screws. McMaster part number: ​7122A12 A 0.9mm size hex driver is needed for the above M2 screws. McMaster part number: ​7289A32


Splitting up the tabs:
#All

The tabs may arrive joined together on a set of sprues. They can be separated using flush cutters, or by simply snapping the sprue with your tool. Then file any remaining sprue material flat. The sprues are strategically located to be hidden after installation.


 

The nylon material can be dyed or painted.

  • Dying:
    • Rit Dye or any Nylon fabric dye may be used.
    • It is not possible to make the colors brighter with dye.
    • Black, Dark green, Dark Red, Dark blue may be achieved
  • Painting:
    • Any plastic compatible paint may also be used, apply in very thin light coats until completely covered. Heavy application may affect tolerances.
    • I have found Ace Hardware Matte Enamel paints to work particularly well.

Natural grey color -vs- black dyed

 

 

    Most 3D printed parts are printed on demand

    The process:

    Batches of up to 15 holsters or other similar sized items are printed, taking up to 20 hours per batch. The parts are then cleaned, and made ready for packing.

    The material:

    Professionally 3D printed SLS Nylon 12 Plastic.

    • Solid part, no hollow or plastic toy feel
    • Material is flexible and water resistant
    • Durable and long lasting
    • Temperature and chemical resistant
    • Ductile and environmentally stable
    • Skin safe

    Material specs and MDS sheets located here.


    Customer Reviews

    Based on 1 review Write a review

    Customer Reviews

    Based on 9 reviews
    67%
    (6)
    11%
    (1)
    11%
    (1)
    0%
    (0)
    11%
    (1)
    C
    Customer

    The thumb tabs were as expected and perfect once fitted. I used the diamond file on the tool itself to take off a slight skim, I expected this would likely be necessary due to their nature.

    D
    D.K.

    They do the job, but i took them off right after.

    M
    MAARTEN Van vliet
    zapwizard netjes opgelost

    Ik had oranje thumb clips besteld.
    Niet de gewenste kleur.
    Een hoop heen en weer gemaild.
    Chapeways nam niet zijn verantwoordelijkheid in deze zaak.
    Maar verschool zich achter zapwizard.
    Die moest het maar oplossen.
    Die deed dat gelukkig ook.
    Bedankt daarvoor.

    Maar chapeways Nederland 🇳🇱🤔
    Nooit meer.

    M
    MAARTEN Van vliet
    Niet de kleur die ik bestelde

    Ik kocht hier twee duimclips voor mijn leatherman surge. De kleur waarin ik ze ontving was flats, bleek, alsof het al 33 jaar in het zonlicht had gelegen.
    Niet de hele felle oranje kleur die ik bij Zapp Wizard in zijn webshopje zag. Het benaderen van de partijen via mail om een antwoord te krijgen op bijvoorbeeld het retour sturen?? Is één groot fiasco en afschuifsysteem. Shapeways Nederland schuift het af op Zapp Wizard en Zapp Wizard antwoord al gauw dit is de kleur die je besteld hebt. Ja dat snap ik zelf ook nog wel dat ik dat besteld heb.
    Het gaat er in deze toch om dat de kleur niet goed is,? niet dat ik een terugkoppeling van jou krijg dat wat ik besteld heb daadwerkelijk ook bij mij aangekomen is?
    1x nooit meer.

    J
    Joseph

    This gets 3 ⭐️because of my own personal issues with trying to shave the tab down enough after I cut it from the sprue so that it fits well. They are on my tool now, and they are a wonderful concept, but just not for me.