Holster for Leatherman Charge Plus & G10

New lower price (Grey only)

The text below changes depending on your selections

This holster is designed to fit the Leatherman Charge+ and Charge+ TTI and the Charge G10 Multitool.

Note: The Bit Extender models are not compatible with the Leatherman Ratchet Driver.

#LeftHandCarry #RightHandCarry #HorizontalLoop

Cross-drawing:

Order a "Left side carry" if you want to cross-draw with your right hand.
Order a "Right side carry" if you want to cross-draw with your left hand.
Order a "Horizontal Loop" if you want a stronger closed belt loop. You can cross-draws from either side with this variant.

• 48x5mm (1.9x0.2in) closed belt loop.
• Fits regular, and Air Force DLATS Belts (BDU) style belts.

#BDULoop

BDU Loop

• 48x5mm (1.9x0.2in) closed belt loop.
• Closed loop is stronger than open clip.
• Fits regular, and Air Force DLATS Belts (BDU) style belts.
• Also attaches to PALS webbing. MOLLE Compatible.
• Features keyhole for hanging on a hook/nail.

#DutyLoop

Duty Loop

• 58x7mm (2.28x0.27in) closed belt loop.
• Fits large, and Duty style belts.
• Also attaches to PALS webbing. MOLLE Compatible.
• Features keyhole for hanging on a hook/nail.

#TekLokCompatible

Tek-Lok Compatible:

• Compatible with Tek-Lok holders.
• Fits Regular, Small and MOLLE small Tek-Lok Models.
• Allows for angled and horizontal mounting. 
• Can also attach to other mid-mount Chicago screw style products.

#MetalClipCompatible

Metal Clip Compatible:

• Metal clip sold separately
• Top-mount Chicago screw hole placement.
• Can also attach to other third party clips that have in-line holes.

Features:

• The tool is is held in place using the two spring-loaded release buttons built into the multitool.
• A channel down the center allows you to remove the tool using just one hand.
• Ultra slim and light design. Less than one ounce. 0.91oz (26g)

How it was designed:

After receiving a few requests for a holster compatible with the Charge TTI, I bought a TTI and got to work. With the titanium scales, I assumed that it would be lighter than the Wave. However the Charge TTI is actually thicker and heavier than the Wave. (0.54lbs versus 0.52lbs). But at least the blade is a stronger type of steel.

I have had owners report that it also fits the Charge Plus and G10

This holster was designed from scratch, following the same methods as my Wave Holster. The tool was carefully measured and a highly accurate 3D model was made. Then in professional CAD software I designed the holster around the tool. The face of the holster is flush with the edges of the tool, allowing the raised brushed metal on the tool to remain a nice accent feature.

What am I getting / not getting?:

This list will update depending on the options selected

Included:

#BDULoop

● One 3D Printed holster with closed BDU Loop

#DutyLoop

● One 3D Printed holster with closed Duty Loop

#MetalClipCompatible

● One 3D Printed holster with holes that allow attachment of a metal clip

#OpenClip

● One 3D Printed holster with a open plastic clip

#LeftHandCarry

● One 3D Printed holster, horizontal carry, left hand side, with a open plastic clip

#RightHandCarry

● One 3D Printed holster, horizontal carry, right hand side, with a open plastic clip

#WithExtender

● A built-in grip for the Leatherman Bit Extender

#All

Not included:

● Leatherman Tool

● Leatherman Bit Extender Accessory

● Driver Bits

#NoExtender

● Built-in Bit Extender Holder

#MetalCLip

● Metal Belt Clip

● Chicago Screws